A factory reset can be the best course of action if your Netgear WiFi extender isn’t functioning as it should—perhaps it’s not connecting to the router, is operating slowly, or is just acting strangely. A factory reset removes any stored networks, passwords, and custom configurations from your device and returns it to its original settings. We’ll explain how to factory reset Netgear extender devices in this blog, along with when to do it and what to do thereafter, including how to set up your Netgear WiFi extender anew.
Let’s begin.
Why Would You Need Netgear WiFi Extender reset?
There are several reasons why a Netgear range extender reset can be required:
- You can’t remember your admin password.
- Router and the extender are not synchronizing.
- Your WiFi signal is no longer being adequately extended by the extender.
- Putting it up somewhere new.
- You’re resolving network problems.
A factory reset Netgear extender can let you start over in any of these situations.
Netgear Wifi Extender Reset Can Be Executed In Two Ways
The Reset button (hardware technique) and the web interface (software method) are the two main ways to reset Netgear extender devices. We will direct you through each of them.
Method 1: Resetting the hardware by pressing the Reset button
This is the most popular and dependable method for resetting a Netgear WiFi extender. Take these actions:
1. Find the Reset button
Typically, the extender’s bottom or back has a tiny, inset hole marked “Reset” that serves as the reset button. To push it, you might need a pin or paperclip.
2. Turn the extender on
After plugging your Netgear extender into an outlet, watch for it to turn on completely. Solid green should be the color of the Power LED.
3. Hold down the Reset button
Press and hold the reset button with your paperclip or pin for ten to fifteen seconds, or until the Power LED blinks or turns off and on again.
4. Hold off until the reboot
Wait for the extender to reset after releasing the button. It might take several minutes. The extender is returned to its original factory settings when the LEDs have stabilized.
This completes the hardware-based reset netgear extender.
Method 2: Software Reset using the Web Interface
You can reset your extender from the admin panel if it can still be accessed using a browser.
1. Attach the extender
Verify that your device is linked to the network (SSID) of the extender. Something like “NETGEAR_EXT” may be this.
2. Go to mywifiext.net in a browser
In search bar, type mywifext.net, then hit Enter. This will straight you to the login page for the extender.
3. Sign in
Put in your administrator credentials. The default keyword is “password,” and the default username is “admin,” if you haven’t modified them.
4. Select Factory Reset
- Navigate to Settings > Other Settings > Factory Reset (model-specific menu titles may differ somewhat). To confirm, click the reset netgear extender button.
- At this point, your extender will restart and go back to its original settings.
Reconfiguring the Extender After the Reset
After you’ve reset your Netgear range extender, you’ll have to start over from the beginning. Here’s how to finish configuring your Netgear WiFi extender:
- The extender should be beavered into a power outlet close to your router.
- Await the solid green turn of the Power LED.
- Make that your device is connected to the default SSID, which is often NETGEAR_EXT.
- Enter mywifiext net in a browser window.
- To relate your extender to home WiFi network, observe the guidelines.
You’ll be asked to provide your WiFi password and select your current network. After that, the extender will use a new SSID (often your current network name with _EXT at the end) to rebroadcast your signal.
Tips For Troubleshooting
If you’re experiencing issues with the setup or reset reset netgear extender:
- Unable to go on mywifiext net? Instead, try using the IP address 192.168.1.250.
- Not resetting the extender? Verify that the device is switched on and hold down the reset button for a whole 15 seconds.
- Have you forgotten your login information? The default combination of “admin” and “password” will be restored upon a factory reset.
Concluding Remarks
A straightforward yet effective troubleshooting method is to reset Netgear extender. A reset can restore performance and dependability, whether you’re fixing connection problems or getting the device ready for a new configuration. Just keep in mind that a reset will remove all of your existing configurations, so you will have to start the Netgear WiFi extender setup procedure over.
FAQs
1. Will resetting my extender delete all settings?
Indeed, a factory reset will return your Netgear extender to its initial factory settings, wiping off any customized settings, including network names, passwords, and configurations.
2. Why should I reset my Netgear extender?
In order to resolve connection problems, lost passwords, configuration failures, or while getting your extender ready for usage in a new network environment, you should reset it.
3. Can I reset my Netgear extender without the Reset button?
Yes, you can reset it using the online interface by going to the settings menu and selecting the factory reset option after logging into mywifiext net.
4. Do I need to set up my extender again after reset?
Yes, in order to reconnect the Netgear WiFi extender to your router and regain internet access after a reset, you will need to finish the setup process over.
5. Can I reset using the web interface?
Of course. If possible, utilize mywifiext net to visit the extender’s admin panel, then select the factory reset option in the settings to reset it.
6. What if the reset button doesn’t work?
If the reset button doesn’t work, try holding it for a longer period of time (15 seconds), make sure the extender is turned on, or, if the web interface is still available, reset using it.